2-Stroke 18HP 246CC Outboard Motor, Water-Cooled Short Shaft Boat Engine, CDI Ignition Tiller Control, 24L External Fuel Tank for Inflatable, Iron, Fiberglass Boats

DetailsCover Locking Handle: There is a locking handle on the cover. If you want to check the motor, then you can open the cover easily with the handle on it.Anti-Vortex Board: The is an anti-vortex board above the propeller. It keeps the water flow steady and you have a good driving experience.Rubber Handle Cap: The handle cap of this motor is made of high-quality rubber, it increases the friction and prevents your hand from slipping.ApplicationThis motor is suitable for rubber boats, inflatable boats, fishing boats, sailboats, yachts, etc.Two-stroke Engine Oil Mixture RatioDuring the Break-in Period 25:1 After the Break-in period 50:125L 1000ML 25L 500ML12L 480ML 12L 240ML10L 400ML 400ML 10L 200ML5L 200ML 200ML 5L 100ML1L 40ML 40ML 1L 20MLSpecificationsType: Two-stroke 18hpGear Positions: F-N-RIgnition System: CDICooling System: Water-CoolingControl System: Tiller ControlStarting System: Manual StartControl System: NO.92 Lead-Free GasolineRecommended Propeller Range: 3-9"1/4''x8"Recommended Lubricant: 2 Stroke Lubricating OilMixing Ratio: Fuel:Oil=50:1Trim And Tilt System: Manual TiltStandard Fuel Tank Capacity: 24L/6.34galDisplacement: 246ccGear Ratio: 2.08(27:13)Cylinder: 2Max.Output(Kw): 13.2Max.Speed(r/Min): 4500-5500Transom Plate Height: 45cm/17.72inBore x Stroke: 5.65cm/2.20x1.97inProduct Size: 78.3x33.2x105.3cm/30.83x13.07x41.46inNet Weight: 38.6kg/85.10lbsGross Weight: 49.5kg/109.13lbsPackage Size: 133x71x38.5cm/52.36x27.95x15.16inHow to UseFirstly, fill the gear oil (open the gearbox lid and fill the gear oil).Secondly, fill NO. 92 petrol in the motor and press the oil pump lightly 6-10 times.Thirdly, fill engine oil and don't exceed the head of the pattern.Fourthly, turn the throttle to the start-up and turn the accelerator gets up to 50%.Then, you should pull the starter line quickly.After the motor starts, please turn the throttle to a running state.Then, you can operate the motor now.Package Included1x Outboard Motor1x Flameout Rope1x Oil Pipe1x Sealing Ring1x Tool Kit1x Paper Pad1x Spark Plug1x Start Rope1x Water Pump Impeller1x Cotter pin1x Fuel Tank1x English ManualNotes1.After in the seawater or turbid water cruising, please use fresh water to clean the outboard motor and cool off the water channel with fresh water.2.The two-stroke outboard engine should use a mixture of two-stroke engine oil and gasoline. And make sure the gasoline and oil are well mixed, otherwise it will damage the machine.3.The new machine has a break-in running period of 10 hours, during which the fuel ratio is gasoline 30L(7.93gal):1L(0.26gal) oil. 10 hours, the ratio is gasoline 50L(13.21gal):1L(0.26gal) oil.4.Before completely running out of cooling water, don't put the outboard motor outside. Otherwise, the water can pass the exhaust port to the air cylinder, which will cause the engine to break down.5.The engine should deposit in places with aridity and good ventilation. You should avoid exposing it directly to the sunshine.6.Before long-term storage, you should clean out the gasoline in the fuel tank completely.7.When there is no water coming out from the motor, please stop using it immediately. You should check the impeller of the water pump and see if the water outlet is blocked.8.Start the motor in the water.9.Use the motor when it stops cycling water.10.Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.11. Two-stroke air- cooled engines must use TCW-2 engine oil, which must be specifically designed for outboard engines.12. Fuel mixture ratio: 25:1 for the first 50 hours, 50:1 after 50 hours.13. Two-stroke outboard engines must use a mixture of 92 gasoline and two-stroke engine oil.14. During the break-in period, the volume ratio of gasoline to oil is 25:1. 15. After the break-in period, the volume ratio of gasoline to oil is 50:1. 16. Important note: Gasoline and oil must be pre-mixed and thoroughly stirred before being poured into the fuel tank. 17. The outboard motor must be started in water, please do not start the engine on land.18. When starting the engine, loosen the vent screw on the fuel tank cap counterclockwise.19. When starting the outboard motor, insert the emergency stop rope and secure the other end to your wrist or belt20. The break-in period lasts approximately 10 hours or one month. Please avoid operating the engine at high throttle during the break-in period.21. After the break-in period, replace the gear oil. The second replacement should be performed after approximately 100 hours or six months.