KAKEI Chainsaw Chain 16 Inch 3/8" LP Pitch .043" Gauge 55 Drive Links- 61PMM3 55 Fits Stihl MS170, MS171, MS180c - 36100050055, R55 (3 Chains) - Semi Chisel

Features

• FIND YOUR CHAINCheck the owner's manual or the guide bar side stamp to find the PITCH, GAUGE, LENGTH and DRIVE LINK NUMBER and select the chain according to these parameters. You are also welcome to contact the KAKEI Customer Support with the chainsaw/bar part number, we are always ready to assist you. (Visit the KAKEI Store for all 60+ sizes)
• Features Germany steel with heating temperature control and punching system make better toughness, Flatness. All saw chain rivets hardened and quenched, resists wear and improves strength, reducing chain tension changes.
• FeaturesJapanese chrome-plated technology creates better durability for cutters, and each of them was grinded and cold-headed with Rotary machines, becomes sharper than ever.
• Saw chain comes with protective oil, resists corrosion.

Description

Chainsaws can be equipped with different guide bars. When selecting a chain for your chainsaw, in addition to the model and length, make sure that the pitch, gauge and number of drive links are correct. You can usually find them on the guide bar side stamp or in the owner's manual. In addition, you are more than welcome to contact KAKEI Customer Support on Amazon with your chainsaw/guide bar part number and we are always ready to help you. STIHL 017, 018, 019, E 140, MS 170, MS 171, MS 180 C, MS 180 C-B, MS 180 C-BE, MS180 G, MS191T, MS 192 C, MS 192 C-E, MS 192 T, MS 192T C-E, MSE 140, MSE 140C Pole Saw: HT7O, HT73, HT75, HT100, HT101, HT130, HT131, HT250 *May take .043" or .050" gauge chain, verify gauge before purchasing *Ensure your model has a 3/8" low profile sprocket 1B4Q55X3 1B0Q55X3 3C368X3 3C381X3 1B4Q44X3 2D0F72X3 1B0Q61X3 For most of the saw chain components, KAKEI uses 68CrNiMo GCr15 imported from Germany, the same raw material used by STIHL, which creates a higher cutting capacity. Extends the chain life by delivering lubricant to key parts of the chain, reducing downtime and maintenance and increasing efficiency. All cutters are electroplated with the industrial hard chrome for better sharpness and longevity. KAKEI hardens and quenches all rivets to improve its strength for fewer chain tension adjustment. In this era of globalization, KAKEI has managed to provide our customers with the Quality& Cost-effective products, which is why KAKEI is trusted by customers all over the world. World-class Production Technology and Equipment World-class Production Technology and Equipment World-class Production Technology and Equipment How to tighten chainsaw chain properly? 1. Disengage the chain brake 2. Loosen the bar nuts 3. Lift the tip of the guide bar 4. Tighten the tensioning screw until the chain sits snugly against the bottom rail of the bar without slack and still rotates freely 5. Re-tighten the bar nuts How to reduce the risk of kickback? If you are not experienced with chainsaws, use a low kickback chain (ANSI standard). Also, never saw using the "kickback danger zone" on the guide bar (the top of the bar tip); use the underside of the bar instead. What is ANSI? The safety standard "B175.1" set by the American National Standards Institute (ANSI), which outlines requirements for gasoline-powered chainsaws (chains), including provisions designed to reduce the risk of kickback injuries when cutting wood. How often should chainsaws be lubricated? Should I use a special lubricant for chainsaws? - Fill the reservoir with lubricant every refueling and ensure the lubricant is properly delivered to the chain during operation. Improper lubrication can cause excessive wear, reduce cutting efficiency and increase the risk of chainsaw damage - Yes Full Chisel vs Semi-Chisel Chain – What's the difference? Full chisel: sharper and cuts faster, but tends to dull when it encounters dirt and is prone to kickback. Semi-chisel: cuts slower than full chisel, but stays sharp longer, suitable in dirty environments. on Amazon Chainsaw Chain KAKEl, a professional garden and logging tools and accessories manufacturer, committed to the advancement of saw chain with advanced technology, first-class equipment and professional product testing procedures. The raw materials of the main components of the KAKEl sawchain are imported from Germany, strictly follow the ISO9001:2015 quality control, and continuously improve product quality to meet customer demand for high-quality products.

Brand: KAKEI

Item Pitch: 0.38 inches

Chain Type: Semi-Chisel

Gauge: 0.04

Item Length: 16 inches

Brand Name: KAKEI

Model Number: 16" 3/8"LP .043" 55DL- German Steel *3

Number of Packs: 3

Number of Items: 3

Manufacturer: KAKEI

Unit Count: 3 Count

Included Components: 3 x Premium German Steel Saw Chains

Manufacturer Part Number: R55

Pitch: 0.38 inches

Chain Type: Semi-Chisel

Gauge: 0.04

Compatible Devices: STIHL MS170, STIHL MS171, STIHL MS180C

Drive Link Count: 55

Item Length: 16 inches

Chain Length: 16 inches