Geeetech Upgrated Version A20T 3D Printer with Triple Color Mixing,Newest GT2560 4.1B Control Board,Filament Detector,Breaking-Resuming,250×250×250mm
Condition: New
Checking for product changes
Buy Now, Pay Later
As low as
/ mo
Learn more
- – Up to 36-month term if approved
- – No impact on credit
- – Instant approval decision
- – Secure and straightforward checkout
Ready to go? Add this product to your cart and select a plan during checkout.
Payment plans are offered through our trusted finance partners Klarna, PayTomorrow, Affirm, Afterpay, Apple Pay, and PayPal. No-credit-needed leasing options through Acima may also be available at checkout.
Learn more about financing & leasing here.
Free shipping on this product
30-day returns
Learn more
This item is eligible for return within 30 days of receipt
To qualify for a full refund, items must be returned in their original, unused condition. If an item is returned in a used, damaged, or materially different state, you may be granted a partial refund.
To initiate a return, please visit our Returns Center.
View our full returns policy here.
Availability:
Only 2 left in stock, order soon!
Arrives
Jul 11 – Jul 17
Features
- Multi-color PrintingThe A20T can combine different spools of filament and extrude them from one nozzle to create multi-color prints.The color mixing is controlled using the Geeetech Color Mixer software,which lets you pick how the colors blend and other specifications.
- Fast Assembly and Quiet PrintingThe printer boasts a modular design that makes it easier to assemble.The build is done in three steps for minimal hassle.Its extruder even has a modularized design that is supposed to make swapping the wires in and out of your extruder a cinch.The A20T has aluminum,v-shaped wheels and rails on each axis to reduce the noise the printer produces.
- Save your Time and Filament Filament detection and print resurrection function provide A20T can continue to print from the same place where it has been stopped,regardless of unexpected power failure or the filament have run out,allow you to change the filament and print it tomorrow.You can also install 3d touch seperately and connect the wifi-module yourself.
- Breaking-resuming Capability & Filament Detector It can continue to print from the same place where it stops, regardless of unexpected power failure, stopping to change the filament, stopping and print tomorrow. Filament Detector will also automatically pause when filament runs out.
- Trustworthy & No WorriesOur products have strict quality inspection test before leaving the factory,and if you have any problem with this printer, please kindly contact us at ANY TIME.
Brand: Geeetech
Material: Aluminum
Color: Multi-color
Item Weight: 29.5 Pounds
Compatible Devices: Laptop, Smartphone
Manufacturer: Geeetech
Brand: Geeetech
Item Weight: 29.5 pounds
Package Dimensions: 19.75 x 19.75 x 12.25 inches
Color: Multi-color
Material Type: Aluminum
Number of Items: 1
Manufacturer Part Number: Geeetech-A20T
Date First Available: August 11, 2020
Frequently asked questions
If you place your order now, the estimated arrival date for this product is:
Jul 11 – Jul 17
Yes, absolutely! You may return this product for a full refund within 30 days of receiving it.
To initiate a return, please visit our Returns Center.
View our full returns policy here.
To initiate a return, please visit our Returns Center.
View our full returns policy here.
- Klarna Financing
- Affirm Pay in 4
- Affirm Financing
- Afterpay Financing
- PayTomorrow Financing
- Financing through Apple Pay
Learn more about financing & leasing here.
Similar Products
Top Amazon Reviews
This printer for me earns several rewards: • Most difficult to get up and running • Most easily to break down • Most picky to 99 things beginners don't know but will absolutely break it. • Worst customer service (tech support is ok, but cs policies suck) Still haven't got one usable print. My previous 3 printers were no problem, by contrast. If you're an expert at settings and printer repair, have at it.
...
show more
Reviewed in the United States on July 10, 2022 by Amazon Customer
So this new purchase arrived as a used/referb unit (stamped with amazon's referb on the box). Parts were not packed well, obvious signs of previous use - plastic still on the hot end nozzle for example. I ultimately sent this one back due to some issues with the build plate, but here is what you need to know if you buy an A20T: * Do yourself a favor and install Marlin firmware 2.x. You're going to need it to do accurate mesh bed leveling * The stock bed leaves much to be desired, and will likely not be flat. Mine was bowed in the center, so no amount of corner adjustment would get it flat. To address this, you will need to manually initiate a mesh leveling of the bed (Install marlin 2.0 and enable LCD mesh leveling). I use 21 point to get a flat build surface. * You will need to calibrate your E-steps for each one, mine was over extruding on all of them. * The hot end have a higher jam rate if you don't keep 3 colors in it, even if you're using 1 extruder. Granted, if you're buying a 3 color printer you're probably going to have 3 colors loaded...but just something to be aware of. * The stock nozzle kinda sucks. Mine was likely damaged/clogged due to it being used. I swapped out for a M7 steel unit and re-leveled. I always recommend ditching factory brass and going with a good new nozzle (either brass or steel, you will replace brass more often). * Showing it's age. The steppers are loud, and it's an old Arduino based board. Not a bad thing, just noisy compared to newer printers * Couldn't get abs to stick to the stock build plate consistently. Might have been a fluke, but I ended up using tape since I know it works. Will it print in multiple colors? Yes. Will it print right out of the box? No way. Expect to spend time getting it dialed in and level, along with finding the sweet spot for your filament temps. Overall not a horrible printer, but not worth the coin unless you explicitly are trying to do 3 color or PVA supports (note: it CAN be done with a mixing hot end, you will just have to set up a tower wipe and fine tune it). For new people to printing, just buy a Neptune2 or something along those lines for excellent prints right out of the box. If you spend the time getting this one dialed in however, it can produce nice results.
...
show more
Reviewed in the United States on November 23, 2021 by NCShooter
I got this printer, it works great. I have read many reviews on here, saying that they cant get it to print one color. This is because the default GCODE has a gradient code inserted, you change that and it works great! Just like any 3D printer you must find out exactly what works for that machine or don't. As with any 3D machine expect a little trial and error to get it dialed in just right. Other reviews on here, show that people expect it to work right out of the box, like all 3d printers. This is not true for any 3D printer to work right out of the box. Do yourself a favor and watch Youtube reviews, they will explain what needs to be done. I am overall very happy with the printer, I just can't stop fiddling with it. However Tech support does need improvement, if you are one of those people that MUST call tech support for everything, then this is not the brand for you.
...
show more
Reviewed in the United States on July 16, 2021 by Chad Brandenburg
We ordered this directly from the company. The box came damaged, but we thought we would try it anyway. It broke when finishing the 1st part. At first they responded, but after a month, we still don't have the parts to fix it and they won't return our messages. Now we have a disappointed kid who hasn't been able to use their new printer/birthday for over a month!
...
show more
Reviewed in the United States on November 6, 2020 by Kris
I've been using this printer since August 2020, have made dozen of prints, and have gotten a decent feel for it. The print bed was a little loose at first, so build adhesion was iffy. After tightening that and re-leveling, prints have gone great. Early on I made a few mistakes and Tech Support provided responses pretty quickly, even sending me replacement parts. Couple of tips: 1.) ALWAYS have filament loaded in every extruder, even if doing single color prints! You risk clogging the unused port(s) in the print head. You'll end up having to drill out hardened plastic to unclog it. 2.) Never mix filament types (e.g. PLA and PETG). Different melting temperatures pretty much guarantee a print failure. There are a few things I wish were better: - Changing the Z-offset during a print does nothing. You have to restart prints to dial in the Z-offset...which is a royal pain. - Replacing the print head thermistor requires removal and disassembly of pretty much the entire print head. Since thermistor wiring is so thin and sensitive, having easier access would be really nice... Overall, I'm very happy with this printer. The color switching and blending features are AWESOME. I'm very glad I went with a more capable printer for my first printer. Have experienced multi-color printing, I could never accept a single filament printer. I've pretty much dialed in PLA printing, but am still "dialing in" PETG. I've had some successful prints, but plenty of failed ones as well. 3D printing is a tinkerers hobby - EXPECT to have failures and thing break; while annoying at times, you'll get to know your printer better each time.
...
show more
Reviewed in the United States on December 21, 2021 by Compucidal Compucidal