GAHQB Electric Skateboard Remote, Suitable for Smart Four Wheel Double Drive Electric Scooter, 4 Speed Controller Electric Skateboards, LED Power/Modes Indicator, TypeC Charging

Features

• Easy Connect: Suitable for most electric motor systems, Firstly, turn on the power of the scooter, then press and hold the scooter power button for 3 seconds. After the scooter indicator light flashes once every 0.5 seconds, the scooter enters pairing mode. Then turn on the power of the remote control. There is a hidden button on the back of the remote control. Press it once to release it. The first light on the remote control will flash. At this time, pairing is successful.
• 4 Speed Modes: Support 4 speed modes, support constant speed mode. Remote control is equipped with convenient functions, such as acceleration or deceleration, forward or braking, reverse, etc.
• LED Power/ Modes Indicator: Support checking remote/scooter battery electric quantity, Function 1: Remote control within three seconds of starting up flash display remote control electric quantity. Function 2:Remote control successfully connect scooter display scooter electric quantity. Function 3: Short press power switch key to switch 4 gears
• 2.4G High-Frequency Stable Control: With 14 meters Remote Receiving Module, Support stable remote control, The sliding direction is always in your hands.
• Low Power Protection: When the remote control battery level is below 20%, the 6th light flashes to remind charging. When the battery level is below 5%, the ""roller"" is prohibited from moving forward. Pulling the ""roller"" backward to brake is normal. If it cannot move forward, it can only brake

Description

1. The main controller connected to power supply 2. Turn on the power, wait for two seconds and then press the on button for about six seconds. Let go immediately when the indicator light flashes 3. Turn on the remote control switch and press button in the lower left corner with small screwdriver 4. Turn off the remote control for two seconds before starting it. Wait for the signal light of remote control and signal light of switch to flash at the same time, indicating that match uccessful Short press the power button Power, the No.1 indicator light will stay on, the 2.3.4.5 indicator lights will flash, and after 3 seconds, they will all turn off. Press and hold the power button for 3 seconds. After the first indicator light goes out, the device has been turned off. The remote control is not connected to the scooter, and it will automatically shut down after 30 seconds. If the remote control is connected to the scooter, it will not shut down automatically. You must wait for the scooter to shut down after it has been disconnected for 30 seconds before shutting it down. Firstly, turn on the power of the scooter, then press and hold the scooter power button for 3 seconds. After the scooter indicator light flashes once every 0.5 seconds, the scooter enters pairing mode. Then turn on the power of the remote control. There is a hidden button on the back of the remote control. Use a long needle to poke the "pairing button" into the small hole and press it once to release it. Do not hold it down for a long time, it will be released in a short time. The first light on the remote control will flash, and the scooter power indicator light will flash once. At this time, pairing is successful and the scooter can be used. Note: Long press the power button on the scooter, short press the remote control. The remote control has successfully connected to the scooter and is ready for use. The 2, 3, 4, and 5 indicator lights indicate the scooter's battery level. The 2nd light has a battery level of "100% -75%", the 3rd light has a battery level of "75% -50%", the 4th light has a battery level of "50% -25%", and the 5th light has a battery level of "25% -5%". If the battery level is below "10% -0%", the 5th indicator light will flash for 0.5 seconds. Within 3 seconds of turning on the remote control, the lights 2, 3, 4, and 5 will flash to indicate the remote control's battery level. Follow the instructions for (light 2 "100% -75%"), (light 3 "75% -50%"), (light 4 "50% -25%"), and (light 5 "25% -5%") battery levels. Display the remote control battery level, and when the remote control battery level is below 20%, the 6th indicator light will flash for 0.5 seconds. Push the "roller" forward to control the skateboard's movement, and pull the "roller" backward to control the skateboard's braking. Pushing the 'roller' forward can switch the speed gear by pressing the button, and pulling the 'roller' backward can switch the brake force adjustment. The scooter is in a stationary state. Press and hold the Reverse button for 3 seconds to switch the front and rear directions of the scooter. When the scooter travels in the forward direction, the first light displays green. Press the Reverse button again briefly to move the scooter backward, and the first light displays red. Repeat the front and rear directions in sequence, and the first light displays green/red. When the scooter is in a stationary state or in a sliding state, press the Power button briefly to switch between the four gears of the scooter. The 5th light of the first gear is always on, the 4th light of the second gear is always on, the 3rd light of the third gear is always on, and the 2nd light of the fourth gear is always on. After successfully switching for 3 seconds, exit. Note that in each gear and when each light is always on, the other 3 lights are not on. Note: First gear is low speed gear, second gear is medium speed gear, third gear is high speed economy gear, and fourth gear is sport player violence gear. Pull the "scroll wheel" backwards on the remote control without releasing it, and press the Power button briefly to switch the brake force of the scooter to four gears. The 5th gear light flashes in one gear, the 4th gear light flashes in the second gear, the 3rd gear light flashes in the third gear, and the 2nd gear light flashes in the fourth gear. Note: Other lights do not light up when each gear and light is flashing. When the signal is lost, if the remote control is in acceleration mode, the scooter stops accelerating and the motor slides freely. When the scooter is in braking mode, the signal is lost and the brake is still effective within 1 second. It can be reconnected within 1 second and can continue to be used. If the signal is lost for more than 1 second, the brake will fail and the skateboard will slide freely. The remote control is charged with Micro USB. After connecting the remote control for charging, the 2.3.4.5 indicator lights on the remote control quickly flash and move. All four lights remain on to indicate that the remote control is fully charged. During charging, the 6th light remains on, which is the charging indicator light. When the battery level of the remote control is below 20%, the 6th light flashes. When the battery voltage is below 5%, pushing the "roller" forward is prohibited, and pulling the "roller" backward brakes normally. If the remote control battery level is below 1% and the voltage is 3.0V, the remote control will automatically shut down. Note: When the battery level of the remote control is below 20% and the 6th indicator light flashes, it is best for the user to charge the remote control in a timely manner to avoid damage to the lithium battery due to overdischarging.

Item Package Dimensions L x W x H: ‎5 x 2.32 x 0.91 inches

Package Weight: ‎0.06 Kilograms

Brand Name: ‎GAHQB

Model Name: ‎Electric Skateboard Remote

Color: ‎Black

Material: ‎ABS

Manufacturer: ‎Electric Skateboard Remote

Included Components: ‎Scooter Remote Control

Size: ‎One Size

Date First Available: March 21, 2025