Search  for anything...
Pellethead

Quadrafire Stove Fan Room Air Blower Fan Pellet, Wood & Gas 812-4900

  • Based on 193 reviews
Condition: New
Checking for product changes
$68.97 Why this price?

Buy Now, Pay Later

As low as $11.50 / mo
  • – 6-month term
  • – No impact on credit
  • – Instant approval decision
  • – Secure and straightforward checkout

Ready to go? Add this product to your cart and select a plan during checkout.

Payment plans are offered through our trusted finance partners Klarna, PayTomorrow, Affirm, Afterpay, Apple Pay, and PayPal. No-credit-needed leasing options through Acima may also be available at checkout.

Learn more about financing & leasing here.

Free shipping on this product

Non-returnable. Transportation of this item is subject to hazardous materials regulation

View our full returns policy here.

Availability: 12 left in stock
Fulfilled by Amazon
Arrives Monday, Jul 21
Order within 15 hours and 20 minutes
Available payment plans shown during checkout

Recently Viewed

Features

  • Quadra Fire Distribution/Convection Blower Replacement
  • Fits several Quadra-Fire & Heatilator Pellet, Gas and wood stove models. Please verify your model and contact us if you require assistance
  • 115V AC, 60Hz, .27 / .84 AMPS, Thermally Protected

Description

Quadra-Fire & Heatilator Stoves Convection/Distribution Room-Air Blower Fits Quadra-Fire Pellet Stove Models: ~ Classic Bay 1200 Insert (CB1200I) Note: The Quadra-Fire CB1200 FS will use a different blower assembly. Please contact us for assistance. ~ Castile Freestanding ~ Castile Insert ~ Santa Fe Freestanding ~ Santa Fe Insert ~ Contour Fits Quadra-Fire Gas Stove Models: ~ Castile GAS ~ Garnet MBK (Does not fit the Garnet DV250) ~ Garnet T ~ Hudson Bay ~ Hudson Bay Insert ~ Columbia Bay ~ Columbia Bay Insert ~ DV400S ~ DV400SL ~ DV40 Step Top ~ DVI25 ~ DVI30 ~ DVI32 ~ GB40 FS (Grand Bay 40) ~ GB40I ( (Serial 253376 and lower) ~ Remington ( QFP30 ) ~ Remington ( QFP40 ) ~ Sapphire ~ Topaz Fits Quadra-Fire Wood Stove Models: ~ 1900 FS ~ 2100 FS (Pre 1995) ~ 2100 Millennium ACT ~ 2100 Millennium ACC (21M-ACC) ~ 2700I (Fireplace Insert. Fits models manufactured before Nov. 2009. Does not fit the new 27i-ACC ~ 3100 Millennium ACC ~ 3100 ACC Step Top ~ 3100 FS (Pre ACT) ~ 3100 FS ACT ~ 4100 FS ~ 4300 FS (Pre ACT) ~ 4300 Millennium ACC ~ 4300 Millenium ACT ~ 4300 ACT Step Top ~ 43ST ACC ~ 4700 ACT ~ 57ST ACC ~ 7100 Fireplace (Pre serial 0091588198) ~ Cumberland Gap ~ Cape Cod ~ Isle Royale ~ Yosemite Fits Heatilator Pellet Stove Models: ~ Eco-Choice PS35 Fits Heatilator Wood Stove & Fireplace Models: ~ Eco-Choice WS18 ~ Eco-Choice WS22 ~ Constitution Fireplace (C40) Pre serial 0091535936 Fits Heat & Glo Wood Stove Models: ~ Northstar Fireplace (Pre-serial 0091535936)

Brand: Pellethead


Color: Convection


Electric fan design: Blower


Power Source: Gas Powered


Style: Modern


Special Feature: Made by Fasco. “Plug & Play” 1.3 AMP, 2400 Full Load RPM, Fits several gas, pellet & wood stoves. See more


Recommended Uses For Product: Air Circulation


Wattage: 31.05 watts


Voltage: 115 Volts


Item Weight: 5.5 Pounds


Brand: Pellethead


Color: Convection


Electric fan design: Blower


Power Source: Gas Powered


Style: Modern


Special Feature: Made by Fasco. “Plug & Play” 1.3 AMP, 2400 Full Load RPM, Fits several gas, pellet & wood stoves.


Recommended Uses For Product: Air Circulation


Wattage: 31.05 watts


Voltage: 115 Volts


Item Weight: 5.5 Pounds


Included Components: Power Cord


Indoor/Outdoor Usage: Indoor


Model Name: QuadraFire 812-4900


Control Method: Touch


Blade Material: Plastic


Manufacturer: Quadra Fire


UPC: 850745008003 859382006236


Package Dimensions: 14.48 x 7.28 x 5.75 inches


Item Weight: 5.5 pounds


Item model number: 812-4900


Is Discontinued By Manufacturer: No


Date First Available: October 17, 2016


Frequently asked questions

If you place your order now, the estimated arrival date for this product is: Monday, Jul 21

This item is non-returnable:

Non-returnable. Transportation of this item is subject to hazardous materials regulation

View our full returns policy here.

  • Klarna Financing
  • Affirm Pay in 4
  • Affirm Financing
  • Afterpay Financing
  • PayTomorrow Financing
  • Financing through Apple Pay
Leasing options through Acima may also be available during checkout.

Learn more about financing & leasing here.

Similar Products

Top Amazon Reviews

    • Works well in Santa Fe pellet stove
The fan blows better than the original but ain't a plug in install. Had to splice two wires together.
Reviewed in the United States on April 16, 2024 by ray parker
    • For 2005 Quadrature Castile free standing - a 100% perfect fit and very quiet*
Item came very quickly. Seller was helpful pre-purchase. Price was more than competitive. Note that this is for a pre-2008 model Castile Free-standing. The ones that you fill the pellets by lifting the black door at the top-rear of the stove not the best design for filling as you have to keep pushing the pellets forward with your hands, to fit a full bag. It may fit newer models, but you will have to check with seller. First, it is super quiet. About the same as when my stove was new. Yes, when keeping it on high speed, you too get some fairly loud fan noise, but no worse than the original. We use it in our main living room where we watch TV and keep it on medium all day, until we go to bed. Then on high overnight, if it's particularly cold (NewEngland). It took me about 20 minutes to replace. Granted, I take this out to clean it after every season, which is probably why I got 15 years out of the original. Do take care when removing/installing/cleaning. NO LIQUIDS! moisture will eventually cause parts to rust a little, which will lead to the screeching noise. The rust will happen over time, due to humidity in off season, but no sense in speeding that up. Also, be gentle with it. If you bend the shaft or bump the air drums the least bit out of center, it could put it out of balance and you will get more noise. There are 2 (out of 4) mounting screws that are impossible to reach. Fear not, if you look at the housing, there are a couple of phillips screws. Take them off and carefully bend down the flap so you can access the screws. Carefully bend back to align the holes for the two screws after installing the blower. Use care in tightening the 4 mounting nuts. Use the new nuts and rubberized washers. Do not over or under tighten and tighten them down with as equal torque as you can. I would say finger tight and maybe 3/4 turn. Basically, you want the rubber to just start bulging, a little, but don't crank it down. The 2 wires were plug and play and I did not need to change any connectors. Highly recommend this. A solid "5". Been using for a few months now, and still 100% happy. ... show more
Reviewed in the United States on April 3, 2021 by Pura Vida
    • Do not over bend fan housing it was a snap to install
Perfect fit I installed this fan replacement on a Quadrafire 5100 wood stove
Reviewed in the United States on November 3, 2023 by Marshall O.
    • 3rd motor and counting Terrible quality.
These motors are low quality. The first one had to be returned cause the end was smashed in and it would not turn without rubbing on cowling. The second made noise when at full operating speed when the fire place reached operating temperature. The third does the same, for some reason the aluminum expands and causes the motors to vibrate and make an irritating whining noise . They only do it when above 50 percent power and when the stove is hot. Drives me nuts for the price I paid and the noise they make. I have to lower the cfm from the knob on the wall dramatically to quiet them down which makes the fireplace much less efficient in putting out hot air into the room. VERY disappointed since I have to remove all the fire brick each time I replace one of these inferior motors. The seller needs to address this problem. I am going to ask seller for full refund on both motors I bought and or replace them for the 4th and 5th time. Update: took both motors out and the plastic squirrel cage fans both warped. These fans are junk and I'm glad I returned them. Installed two new ones from different vendor ... show more
Reviewed in the United States on December 2, 2019 by ALL LIFES MAYTER
    • This is what I wanted
The hardest part of this job was figuring out what I needed to order for our Quadrafire 3100-F blower. I guess we got 20 years out of the old one, but knowing whether a potential replacement fit our specific model was hard to pin down. This worked great, and seemed to be one of the less expensive alternatives I had to choose from. One thing I learned was I need to get in there and vacuum off the dust bunnies annually (or more). The old blower was clogged with dust in just about every imaginable place (and in some places beyond imagination). Stove hygiene is now a thing with me. ... show more
Reviewed in the United States on January 28, 2020 by M. Bramel
    • Not quite an exact replacement - expect to have to do some work to install it
I validated the part number for the replacement blower before making the purchase. Even though the part number matches, upon receiving the blower and trying to install it, it did not fit. The metal "feet" or bracket that it sits on is slightly larger than the original blower that I was replacing. The stove has rails that this blowers feet have to fit in between in order to be installed. This blower did not fit. I had to do some metal working on the feet to resize them to get them to fit within the rails on the pellet stove. Also, the electrical connections, or more specifically the plastic shrouds on the electrical connections, were not large enough to fit over the plastic shrouds on the electrical connections coming from the stove. As a result I had to peel back the plastic shrouds in order to get the metal connections to make contact. This was a good price, but it was not a quick 15 minute install like I had hoped it would be. Finally, I think that the new blower does not blow as much air on the low setting as the original blower. I don't have the motivation to uninstall the new one and reinstall the old one just to test this out. It seems ok on the medium and high settings though. ... show more
Reviewed in the United States on January 19, 2021 by PeteCIS
    • quadrafire 3100 wood stove
had to take this unit apart and re configure, to fit my stove... but it worked well and replaced my oem blower perfectly. I removed squirrel cages from blower housings detached blower housing, rotated 90 degrees, re attached and re assembled. matched the old assembly perfectly... works well.
Reviewed in the United States on December 1, 2022 by Random
    • Perfect fit!
The stove sits in our living room right next to our chairs. The fan is reasonably quiet and does not interfere with the TV. Definitely blowing more heat now and we are enjoying it very much. I would recommend anyone looking for a replacement to consider this unit.
Reviewed in the United States on December 24, 2021 by R Phillips

Can't find a product?

Find it on Amazon first, then paste the link below.