Husky Liners 79121 Black Wheel Well Guards Rear Wheel Well Guards Fits 2015-2019 Ford F-150 (will not fit Raptor)

1.0 out of 5 stars

By Kate - Reviewed in the United States on May 1, 2017

Notice an area that looks like a channel that’s approximately 2

BEWARE OF THIS PRODUCT! I ordered this for my 2016, F150, Crew Cab, 4x4. I should have listened to other negative feedback. I wrongfully assumed the complaints of not fitting properly were a small percentage. Unfortunately, they right & I should have heeded their warnings. Product gets -2 stars the following reasons. 1. Many of the other negative feedbacks mentioned having difficulty getting the pre-drilled holes to line up, but I couldn’t even get that far. The right side guard was improperly manufactured on the forward/lower corner. After trying to bend, twist, and push the item into place, I decided to measure how much clearance I had for the stiff plastic to fit into. F150 owners, look at the forward/lower edge of the passenger side fender well as if you’re trying to look toward the rear of the vehicle from inside the wheel well. Notice an area that looks like a channel that’s approximately 2.5” wide. The guard that’s at least 3” is supposed to fit inside that 2.5” area. The only way to get it to fit is to grab your handy-dandy blade and start cutting away at the plastic. Even after trimming the item, it still didn’t fit properly for some. After fighting with it for over an hour, I decided I had enough. 2. Although I was disappointed in my wasted time, I was content in “thinking” that since the item did NOT meet specifications, that Husky would reimburse me with no questions asked. I contacted Husky through the return process and explained my all too common dilemma. They promptly sent a shipping label BUT it wasn’t free. Obviously I thought something was wrong because #1; we are longstanding Amazon Prime customers and have never had problems; #2 the product was obviously defective; #3 Husky HAS to know that this product has very poor quality control. Insult to Injury! The defective parts cost $94 with free shipping with Amazon Prime. BUT, it cost $70 to ship the item back, which comes out of your refund. So essentially, you pay $24 dollars to piss yourself off. In closing... Please understand that I typically provide 1-3 sentence comment, post my star rating, and get on with my busy life. But I felt that it was worth sharing so others don’t make the same mistake. P.S. This was originally 588 words - cut it down to the 400 word limit.

5.0 out of 5 stars

By JFixit - Reviewed in the United States on May 14, 2018

Fits 2018 F150 4x4 Perfect - sides are NOT interchangeable!

Fit perfect and all 4 holes lined up on my 2018 F150 4x4 with no issues if you get them on the correct side (not interchangeable AND make sure the liner is not catching on the inner lip. Both sides look nearly identical and I did not see the stamp per instructions for Driver vs Passenger side. Driver's side is ~18.25" OC for the 2 top holes and Passenger's side is ~21" OC. Slide the 2 clips over the back holes as shown in the instructions, slide cover over wheel (I did on a slight angle and opposite from the shock). Slide the liner in place by pushing up and back at the same time. The center and one side go in fairly easy. The other side I put my hand between wheel lip (to protect the paint) and liner and gently pushed back and bent into place. Careful as it may hang up on the lip of the inner fender where it is spot welded. These fit better than the Chevy OEMs I had on my previous Silverado. I loosely tightened the 2 screws in the back clips and then you will need a stubby Philips to screw the bottom 2 holes if you leave the wheels on. The clips for the bottom holes go on the back of the OEM hole and act as a nut (do not slide over the hole like the back top 2). Took me only 15 minutes a side once I measured and figured which liner went on which side. Only thing I had to do was use a razor and remove some of the material still clinging where they drilled the 4 holes per liner.

5.0 out of 5 stars

By S Mack - Reviewed in the United States on December 30, 2015

Great look and function. Super easy to install. Should be supplied by Ford.

Installed these on my 2015 Ford F150 Supercrew. They look great, fill up the wheel well and prevent mud etc from getting in the shocks/ undercarriage area. They fit and look great. Well made and a great price (about 1/2 the stock Ford product). Like others have stated; the front most hole doesn't line up, but it took less than 1 minute to punch one through and use the supplied hardware. Odd that they haven't fixed this, but it's not even enough of an inconvenience to drop a star. If you can't discern from the above; super easy to install. Just requires a little muscle to fold it into place behind the fender. All pro, no cons. Excellent product. Thank you for reading, if this was helpful please check yes below.

5.0 out of 5 stars

By C4DB - Reviewed in the United States on August 26, 2015

Great product, easy install.

Excellent fit - 20 minute install (first time, reading instructions as you go), big difference in keeping mud out of body panels, frame parts and other components, also adds to street appeal - smooth black backing behind wheel really makes the truck look better. Good product, promptly shipped, delivered to the door. Installation requires only 1 short Phillips #2 screwdriver - holes provided by Ford (uses existing mounting holes - 2015 F150 FX4).