Search  for anything...
Creality

Creality 3D Printer Ender 5 Plus FDM Printer with Auto Bed Leveling Sensor Kit (Ender 5 Plus)

    • Based on 15 reviews
Condition: New
Checking for product changes

Notify me when this product is back in stock

$509.00 Why this price?
Save $39.99 was $548.99

Buy Now, Pay Later

As low as / mo
  • – Up to 36-month term with PayTomorrow
  • – No impact on credit
  • – Instant approval decision
  • – Secure and straightforward checkout

Ready to go? Add this product to your cart and select a plan during checkout. Payment plans are offered through our trusted finance partners Klarna, PayTomorrow, Affirm, Apple Pay, and PayPal. No-credit-needed leasing options through Acima may also be available at checkout.

Learn more about financing & leasing here.

Selected Option

Free shipping on this product

This item is eligible for return within 30 days of receipt

To qualify for a full refund, items must be returned in their original, unused condition. If an item is returned in a used, damaged, or materially different state, you may be granted a partial refund.

To initiate a return, please visit our Returns Center.

View our full returns policy here.

Availability: Unavailable
Fulfilled by Amazon
Available payment plans shown during checkout

Recently Viewed

Model: Ender 5 Plus


Features

  • Auto Bed Leveling Sensor Kit - Creality Ender 5 Plus 3D printer has auto bed leveling sensor which can precisely measure the tilt of hotbed surface and offers Z axis leveling compensation. Saving your time and reducing waste.

Brand: Creality


Material: Tempered Glass


Product Dimensions: 24.88"D x 24.37"W x 26.22"H


Item Weight: 61.9 Pounds


Compatible Devices: Laptop


Product Dimensions: 24.88 x 24.37 x 26.22 inches


Item Weight: 61.9 pounds


Manufacturer: Creality


Country of Origin: China


Item model number: Ender 5 Plus


Warranty Description: 1 year


Batteries required: No


Included Components: 3d printer


Frequently asked questions

This product is currently out of stock. Please check back later for shipping info.

Yes, absolutely! You may return this product for a full refund within 30 days of receiving it.

To initiate a return, please visit our Returns Center.

View our full returns policy here.

  • Klarna Financing
  • Affirm Pay in 4
  • Affirm Financing
  • PayTomorrow Financing
  • Apple Pay Later
Leasing options through Acima may also be available during checkout.

Learn more about financing & leasing here.

Similar Products

Top Amazon Reviews

    • Works great!
Model: Ender 5 Plus
Took a little bit to get it level, but once I did, I started printing BIG stuff. I’ve had an Ender 3 for 3 years, so I didn’t have to learn anything new. The biggest downside is it still has the old style main board, so the stepper motors are really noisy. I ordered a silent board for it.
Reviewed in the United States on December 18, 2023 by Jeffrey R. Bright
    • Don’t buy
Model: Ender 5 Plus
I have had this for a few weeks now and I have had nothing but problems with it. I have tried everything and I only got one print to work. I’m so disappointed in this
Reviewed in the United States on December 1, 2023 by Alisha Larue
    • it can work but setup and firmware upload a pain
Model: Ender 5 Plus
If you do not need the 350mm print size spend more get better. If you do go with this printer a magic eight ball is a better then tech support. Here are some setup items you need to know. You cannot run this printer well without a sonic pad. The BL touch auto level is not even close to correct. To upload the firm ware you need a 8gb micro sd card formatted with 4kB packets. This has to be done on a windows machine. Standard cards are 32kB packets. Do the update before any assembly. Open the bottom of the controller. Disconnect power. Insert the micro SD card with the latest firmware from Creality. Connect power. Leave the bottom off. Power up. Stand there and make sure you see the file upload followed by a bunch of screens. No screens. Power down and power up again. Remove card and insert into the slot on the side. Power up and see if the main mother board updates. If stuck on the creality screen or a single line of Chinese text, power cycle and try again. If after 6 tries it does not work you need to plug the controller into your computer using hexuploader, set the baud rate to 115200, and upload the .hex file using hex uploader. If you cannot get the firmware to update pack it up and send it back. Sonic pad updates have to be done with the sonic pad plugged into the router. Not wireless. Creality does not support the sonic pad silent mother board combination. Give the Sonic pad a static ip address by setting it to fixed in your router. Do not using the springs for the bed. Order silicon ones and the better blue turning wheels. Do not use the filament feed system. Order the upgrade and a steel gear instead of the brass. Disconnect the motor wires when your are manually adjusting the z x y axis. Put the glass on and use small binder clips about 1.5” from each corner on the same axis as the controller. The z screws need to be manually adjusted using a .5mm ruler to ensure that the bed is the same height from the top. You can use the motors and controller to get you close to the top but the motors have to be disconnected to screw on side or the other. With the Z adjusted, move x y axis bar to both ends and measure at each of the 4 corners. Do not crank the silicon springs down tight as this will cause the bed to bend on the corners. Leave some play. Get the measurements and close as possible. Then use the sonic pad to level the bed. The bed leveling is a compromise. You want the corners to be around minus .05mm and the to be positive .01 or .02mm. A minus number means loosen the blue adjustment wheels. Adjusting one cornet will throw the others off. There is a lot of back and forth. At the beginning if one side is much more negative, disengage the z motors, hold on screw still and adjust the other by hand. Once leveled make a 300mm by 20mm by 2mm high calibration print. You will most likely come up short. Divide the 300 by the result and this is your adjustment factor. With the printer and sonic pad on you can go to your web browser, enter the ip address, and access the config file using the {..} button in the browser. Double click on the file, scroll down and apply the multiplier to the e z x and y rotation. For example should be 300 but is 298.8m or 1.004. Divide the x y z by the 1.004 and enter the number. Then save. If longer do the opposite. Power cycle and reprint. You will also need a 20mm by 250mm tower to check the z. You can also use the 300mm calibration file to fine tune the head height until you are squishing the material but do not have or have tiny ripples. ... show more
Reviewed in the United States on November 19, 2023 by Karen C.
    • Good value for money
Model: Ender 5 Plus
Straight out of the box, its limited in capabilities but with some small modifications and improvements its a solid printer
Reviewed in the United States on December 17, 2023 by Gabe Taylor
    • Awesome printer!!
Model: Ender 5 Plus
Review Image by J J
Review Image by J J
Review Image by J J
Review Image by J J
Let me start by saying that I have been using an original acrylic framed anet A8 that I bought in 2018. Coming from that, the Ender 5 Plus is amazing. The print area is huge and it was very easy to assemble. It comes mostly assembled and has a lot of QoL stuff I didn't have before, such as the BL Touch, filament runout sensor, touchscreen, and print resume on power loss. I put it together in about 30 minutes. Took about 5 to 10 minutes for the autolevel to run. After that it has just been printing nicely with no problems. Also I used the included 200g spool of white to print the letter holder pictured and there were no snags in the roll, it took 183g and 12 hours to print. Overall I am extremely satisfied with this printer. ... show more
Reviewed in the United States on September 15, 2023 by J J
    • does not work
Model: Ender 5 Plus
Recently purchased, can not get filament to feed which renders it useless, very disapointed.a
Reviewed in the United States on January 2, 2024 by Charles H Rollins
    • Not usable out of the box
Model: Ender 5 Plus
This printer was pretty much useless out of the box. It could print tiny pieces, no problem, but anything over 4-5”, and the part would just not stick. The problems are many with the way the printer is shipped: Loose parts, misalignments, bad firmware, poor calibration, etc. If you’re willing and able to spend days researching and figuring out how 3D printers really work, flashing new firmware, printing calibration parts and tweaking mechanical parts and your slicer settings, then you’ll get this printer to work eventually. Otherwise, you’ll throw up your hands like so many on Reddit! ... show more
Reviewed in the United States on December 23, 2023 by wherati
    • Excellent printer, just takes a little tinkering!
Model: Ender 5 Plus
This printer works pretty well! I've had mine for about a year. It takes a little while to setup out of the box, but overall not too terrible if you have some mechanical knowledge. I would recommend replacing the filament tube with a capricorn tube right out of the box. It will save you a ton of headaches. ... show more
Reviewed in the United States on October 17, 2023 by RF

Can't find a product?

Find it on Amazon first, then paste the link below.