Youxmoto Centrifugal Go Kart Clutch 3/4 Bore 10 Tooth with #420 Chain (96 links), Works 2-6.5hp, 2300±300 RPM, Compatible With#40 41 Chain, for Lifan 196cc, for Honda GX160/GX200, 3/4" Shaft (19.05mm)

Features

• BROAD COMPATIBILITY: This go kart clutch and chain fit for Yerf-Dog Go Kart / for Tecumseh, fit for Baja MB165 and MB200 Minibike, including for Baja Heat, for Mini Baja/ for Baja Warrior. NOTE: 1, Apply lubricating oil before use; 2, After installation, start it 3-5 times for running-in
• FITMENT: Fit 2- 6.5HP Small Engines, fit for HONDA GC160, GC190, GX120, GX140, GX160, GX200. And fit for BS and 2-6.5 HP with 3/4" Shaft. fit for Tecumseh Engines 2-6.5 HP with 3/4" Shaft.
• Usage Tip 1: Before using the product, you can drop lubricating oil above the retaining ring, fill it up in a circle, wait for it to seep in, then rotate the clutch. If there is no obstruction during rotation, there is no need to disassemble it. (The oil dripping position can be seen in the picture below)
• Usage Tip 2: When this product is first installed and started to operate, it needs to be run-in 3 to 5 times to avoid the problem of insufficient contact area of the internal parts of the clutch due to insufficient speed, which may cause slippage and smoke due to friction. The specific measurement steps are as follows: First, run the engine no-load until the clutch is engaged for the first time, hold for 10 seconds, and then turn off the engine to cool down. Second, gradually increase the load three times, from 0 to full speed, with a 2-minute interval for cooling each time. If there are no issues with the appeal process, it can be used normally.
• WORK WITH: Go Kart Clutch 3/4" Bore 10 Tooth Sprocket with 40/41/420 Chain designed for 2-7Hp 212cc Predator engines clutch performance parts.
• WARM TIPS: 3/4-inch centrifugal clutch for single wheel belt direct drive karts with tires No Larger Than 15" tall.
• Quick reply: Quick reply within 8 hours; Provide technical support, If you encounter any questions on our Products.

Description

🏎️Features:✔️Assembly compatible with Baja Mini Bike, for Baja Heat, for Mini Baja, for Baja Warrior.✔️It is compatible with MB165 and the newer MB200 models.✔️This item is also a perfect replacement part on much small utility 163cc 5.5 Hp and 196cc 6.5 Hp engines.🏎️Specification:Clutch Bore: 3/4"Sprocket: 10 teeth with 3 Feet 40/41/420 chainClutch Diameter: 107 mmClutch Height: 55 mmEngagement Speed: 2300±300 RPMRecommended Engine: 2 HP - 6.5 HP, 3/4" shaft with flat key🏎️Fits:Fit 2-6.5hp for Honda Cloned Engines GC160, GC190, GX120, GX140, GX160, GX200Perfect For Go Kart Minibike / for Baja MB165 & MB200 (Heat, Mini, Warrior)Common clutch for 3.5-7hp engines using 40/41/420 chainFit for BS and 2 - 6.5 HP With 3/4" Shaftfit for Tecumseh Engines 2 - 6.5 HP With 3/4" Shaft🏎️Package: 1 x 10 teeth centrifugal clutch1 x 40/41/420 chain1 x Connecting link🏎️Oiling the clutch is extremely importantBehind the snap ring, next to the sprocket teeth at the end of the clutch. There's an internal bronze bushing behind the snap ring that requires lubrication and it's up to you to put it there each time.It's a good idea to oil the chain at the same time. If the chain gets kinky from lack of oil it should be replaced before it damages the clutch sprocket. A new chain is cheaper than a new clutch.❤️Note:The Centrifugal Clutch 3/4" needs to be oiled before use.Before ordering please check your crankshaft size.Don't put oil inside the clutch holes

Manufacturer: ‎Youxmoto

Brand: ‎Youxmoto

Model: ‎Clutch

Item Weight: ‎4.13 pounds

Product Dimensions: ‎0.5 x 0.5 x 0.5 inches

Item model number: ‎LFTOC003-LYF

Exterior: ‎Polished

Manufacturer Part Number: ‎LFTOC003-LYF

Date First Available: September 27, 2022